Some light incubators are made of stainless steel, but all metal surfaces exposed to corrosive environments are electrochemically or chemically reacted and are evenly corroded. The part of the stainless steel surface passivation film with weak corrosion resistance forms a pitting reaction due to the self-excited reaction, and generates small holes, and the chloride ions are close to form a strong corrosive solution to accelerate the corrosion reaction rate. There is also intergranular corrosion cracking inside the stainless steel, all of which destroys the passivation film on the stainless steel surface.
Therefore, the stainless steel surface must be regularly cleaned and maintained to maintain its gorgeous surface and extend its service life. When washing the stainless steel surface, care must be taken not to cause surface scratching. Avoid using bleaching ingredients and abrasive washing liquid, steel balls, grinding tools, etc. To remove the washing liquid, rinse the surface with clean water at the end of washing.
1. The oil, oil and lubricating oil on the stainless steel surface of the incubator are contaminated, wiped clean with a soft cloth, and then cleaned with a neutral detergent or ammonia solution or with a special detergent.
2. The trademark and film of the stainless steel surface of the light incubator are washed with warm water, weak detergent, and the adhesive component is scrubbed with alcohol or organic solvent.
3. Light incubator Stainless steel surface with dust and easy to remove dirt, can be washed with soap, weak detergent or warm water.
4. The light incubator has a rainbow pattern on the surface of the stainless steel, which is caused by excessive use of detergent or oil. It can be washed with warm water detergent during washing.
5. Light rust caused by dirt on the stainless steel surface of the incubator can be washed with 10% nitric acid or grinding detergent, or with special washing drugs.
6. Light incubator Stainless steel surface with bleach and various acid adhesion, rinse immediately with water, then dilute with ammonia solution or neutral carbonated soda solution, wash with neutral detergent or warm water.
As long as we use the correct maintenance method, we can extend the service life of stainless steel and keep it clean, bright and gorgeous.
Therefore, the stainless steel surface must be regularly cleaned and maintained to maintain its gorgeous surface and extend its service life. When washing the stainless steel surface, care must be taken not to cause surface scratching. Avoid using bleaching ingredients and abrasive washing liquid, steel balls, grinding tools, etc. To remove the washing liquid, rinse the surface with clean water at the end of washing.
1. The oil, oil and lubricating oil on the stainless steel surface of the incubator are contaminated, wiped clean with a soft cloth, and then cleaned with a neutral detergent or ammonia solution or with a special detergent.
2. The trademark and film of the stainless steel surface of the light incubator are washed with warm water, weak detergent, and the adhesive component is scrubbed with alcohol or organic solvent.
3. Light incubator Stainless steel surface with dust and easy to remove dirt, can be washed with soap, weak detergent or warm water.
4. The light incubator has a rainbow pattern on the surface of the stainless steel, which is caused by excessive use of detergent or oil. It can be washed with warm water detergent during washing.
5. Light rust caused by dirt on the stainless steel surface of the incubator can be washed with 10% nitric acid or grinding detergent, or with special washing drugs.
6. Light incubator Stainless steel surface with bleach and various acid adhesion, rinse immediately with water, then dilute with ammonia solution or neutral carbonated soda solution, wash with neutral detergent or warm water.
As long as we use the correct maintenance method, we can extend the service life of stainless steel and keep it clean, bright and gorgeous.
Tof(Time-of-flight), is JRT new product, which is a single-point LiDAR sensor. With a micro size of 46x17x7mm, customers can widely use in many Laser Measurement Solutions. The lidar distance sensor can measure 12m short-range. It's great for Unmanned Aerial Systems.Contact Us Now for data sheet.
| Product Name | Tof LiDAR Sensor |
| Model Number | IT02S-65-A/IT02S-65-B/IT03M-650 |
| Measuring Range (without Reflection) | 0.1-12m/0.1-10m/0.1-15m(90% reflectivity) |
| Place of Origin | China |
| Accuracy | 2cm~4cm/5cm |
| Blind Area | 10cm |
| Resolution | 1cm |
| Measuring Unit | centimetre |
| Laser Class | Class II, red |
| Laser Type | 650nm, <1mW |
| Communication Interface | UART, 115200bps(default) |
| Size | 46*17*7mm/50*26*13mm |
| Weight | About 4g/10g |
| Voltage | 2.7V~+3.6V |
| Electrical Level | TTL/CMOS |
| High Frequency | 100hz |
| Operating Temperature | 0-40 ℃ (32-104 ℉ ) |
| Storage Temperature | -25~60 ℃ (-13~140 ℉) |
ToF Sensor,Time of Flight Sensor,LiDAR Distance Sensor,ToF Distance Sensor
Chengdu JRT Meter Technology Co., Ltd , https://www.rangingsensor.com