Outdoor bags of mushrooms, raw materials are widely available, bio-conversion rate of 8 to 10 times higher than the section of wood cultivation, and high quality and efficiency. In order to produce more and better shiitake mushrooms, I constantly explored in the production, summed up a set of mushroom color management methods, greatly improving the number and quality of fruiting. This set of methods is now described as follows:
"One control": That is, the initial control of temperature. After 3 to 4 days after bag removal, the temperature inside the mushroom bed cover film is controlled within 25°C. It is not necessary to remove the film for ventilation. The purpose is to allow the unpacked shiitake mushrooms to rejuvenate at moderate temperatures. After 4 days ventilation every day 1 or 2 times (time 30 to 40 minutes), pull the temperature difference, so that the aerial mycelium is inhibited, and will not be too prosperous.
"Two sprays": The secretion of water spray off. Generally 7-8 days after bag removal, the mycelium begins to spit out yellow water beads, and this should be treated in time, otherwise it will cause autolysis of the bacteria and be easy to infect the bacteria, or cause the bacteria to be thickened. To do this, it must be sprayed with water in a timely manner. On the first day, lightly spray on the tube with a sprayer, dilute the yellow waterdrops, and rinse with a heavy pressure sprayer the next day. When the tube is slightly dry, cover the film.
"Three difficult solutions": that is to change the color difficult. Mainly do a good job of ventilation (not less than twice a day, 30 minutes each time). When the temperature is high, sooner or later, it is necessary to remove the membrane and ventilate the temperature, so as to increase the temperature difference, the temperature of the mushroom bed during the color conversion period is controlled at 15°C to 20°C. If it is found that the color change is too light or does not change color, spray water to moisturize, tightly cover the film, or put the fungus tube on the ground. Use ground temperature and wetness to promote the color change; if the mycelium grows and does not fall down, it can be removed at noon. 1 to 1.5 hours, let the tube contact with light or dry air, prompting the mycelium to fall into color. If the above treatment is not effective, use 3% lime water to lightly spray and wait for a little dry cover film.
"One control": That is, the initial control of temperature. After 3 to 4 days after bag removal, the temperature inside the mushroom bed cover film is controlled within 25°C. It is not necessary to remove the film for ventilation. The purpose is to allow the unpacked shiitake mushrooms to rejuvenate at moderate temperatures. After 4 days ventilation every day 1 or 2 times (time 30 to 40 minutes), pull the temperature difference, so that the aerial mycelium is inhibited, and will not be too prosperous.
"Two sprays": The secretion of water spray off. Generally 7-8 days after bag removal, the mycelium begins to spit out yellow water beads, and this should be treated in time, otherwise it will cause autolysis of the bacteria and be easy to infect the bacteria, or cause the bacteria to be thickened. To do this, it must be sprayed with water in a timely manner. On the first day, lightly spray on the tube with a sprayer, dilute the yellow waterdrops, and rinse with a heavy pressure sprayer the next day. When the tube is slightly dry, cover the film.
"Three difficult solutions": that is to change the color difficult. Mainly do a good job of ventilation (not less than twice a day, 30 minutes each time). When the temperature is high, sooner or later, it is necessary to remove the membrane and ventilate the temperature, so as to increase the temperature difference, the temperature of the mushroom bed during the color conversion period is controlled at 15°C to 20°C. If it is found that the color change is too light or does not change color, spray water to moisturize, tightly cover the film, or put the fungus tube on the ground. Use ground temperature and wetness to promote the color change; if the mycelium grows and does not fall down, it can be removed at noon. 1 to 1.5 hours, let the tube contact with light or dry air, prompting the mycelium to fall into color. If the above treatment is not effective, use 3% lime water to lightly spray and wait for a little dry cover film.
Our Pp Resin pellet has a variety of uses in the pharmaceutical packaging industry. The original materials that come to our factory will go through a series of strict tests to ensure the quality. Then we will mix the corresponding raw materials with an appropriate proportion. When everything is ok, we will go to the production procedure. During the whole production process, we have specific quality management system to guarantee the quality.
Pp Resin For Plastic Bottle,Pp Resin For Bottle,Pp Resin For Water Bottle,Plastic Raw Material Pp Resin
SUZHOU CRH PHARMACEUTICAL TECHNOLOGY CO.,LTD , https://www.crh-health.com