Causes and troubleshooting methods for common faults in pelleting machines:
Common faults of this machine:
1. After the machine is powered on, the motor does not run.
cause:
1. Poor contact of the power cord or loose power plug;
2. Poor contact in the switch.
Remedy (you must turn off the power to do the following):
1. Repair the power supply or exchange the plug of the same specification;
2. Repair or replace the same size switch.
Common faults of this machine:
When the mechanism is pill, the shaft knife rotates or the medicine surface sticks.
cause:
The output stop lever is loose and there is a distance from the bottom of the shaft cutter. The pill cannot be scraped off the shaft slot.
Remedy (you must turn off the power to do the following):
Adjust to the distance between the discharge plate and the bottom of the shaft sipe, (about 0.1mm) and tighten the set screws.
Common faults of this machine:
When the unit is working, the motor stops suddenly.
cause:
1. Capacitance is broken.
2. The gear is stuck.
Remedy (you must turn off the power to do the following):
Check the gear slots for debris and clean them.
Common faults of this machine:
When the machine is working, the shaft cutter has a slight jump.
cause:
Block compression screw loosening <br> <br> troubleshooting (must be cut off, in order to perform the following operations):
Open the top cover and tighten the 6 hexagon socket screws evenly.
Common faults of this machine:
The machine during operation, abnormal noise <br> <br> Reason:
1. The shaft knife and the friction part of the body are dry and oil-free;
2. There is no oil between the gears.
Remedy (you must turn off the power to do the following):
1. Inject a few drops of clean cooking oil into the oil eye;
2. Apply a small amount of butter to each gear groove.
Common faults of this machine:
The heater has failed to heat up.
cause:
1. The plug is loose or the power cord is off;
Remedy (you must turn off the power to do the following):
Replace the plug of the same specification or repair the power socket;
Common faults of this machine:
1. After the machine is powered on, the motor does not run.
cause:
1. Poor contact of the power cord or loose power plug;
2. Poor contact in the switch.
Remedy (you must turn off the power to do the following):
1. Repair the power supply or exchange the plug of the same specification;
2. Repair or replace the same size switch.
Common faults of this machine:
When the mechanism is pill, the shaft knife rotates or the medicine surface sticks.
cause:
The output stop lever is loose and there is a distance from the bottom of the shaft cutter. The pill cannot be scraped off the shaft slot.
Remedy (you must turn off the power to do the following):
Adjust to the distance between the discharge plate and the bottom of the shaft sipe, (about 0.1mm) and tighten the set screws.
Common faults of this machine:
When the unit is working, the motor stops suddenly.
cause:
1. Capacitance is broken.
2. The gear is stuck.
Remedy (you must turn off the power to do the following):
Check the gear slots for debris and clean them.
Common faults of this machine:
When the machine is working, the shaft cutter has a slight jump.
cause:
Block compression screw loosening <br> <br> troubleshooting (must be cut off, in order to perform the following operations):
Open the top cover and tighten the 6 hexagon socket screws evenly.
Common faults of this machine:
The machine during operation, abnormal noise <br> <br> Reason:
1. The shaft knife and the friction part of the body are dry and oil-free;
2. There is no oil between the gears.
Remedy (you must turn off the power to do the following):
1. Inject a few drops of clean cooking oil into the oil eye;
2. Apply a small amount of butter to each gear groove.
Common faults of this machine:
The heater has failed to heat up.
cause:
1. The plug is loose or the power cord is off;
Remedy (you must turn off the power to do the following):
Replace the plug of the same specification or repair the power socket;
China Extract Powder For Use As Dietary Supplement Extract Powder, Extract Powder Manufacturer
Shaanxi Kang New Pharmaceutical co., Ltd. , https://www.bio-pharmacies.com