The front of the CO2 incubator has an operation panel with power switch, temperature regulator (manual and liquid crystal display), CO2 injection switch, CO2 adjustment knob, humidity adjustment knob, temperature display panel, CO2 display panel and Humidity display disk, carbon dioxide sample hole (used to extract the sample in the box to detect whether the CO2 in the box reaches the content displayed on the display panel) and alarm device (over temperature warning light).
(1) The incubator should be placed in a relatively stable position and away from heat sources to prevent temperature fluctuations and microbial contamination.
(2) Before turning on the power, add a certain amount of distilled water in the incubator according to the instruction manual (add the amount of disinfectant to the water added, see the instructions for details) to avoid burning the machine.
(3) When the water is added to a certain amount, the alarm light is on, that is, the water supply is stopped, and the power switch is turned on, that is, the heating is started, and the temperature controller is adjusted to the required temperature.
(4) When the temperature reaches the required temperature, the heating is automatically stopped. When the required temperature is exceeded, the over-temperature warning light is on and an alarm sounds.
(5) The CO2 used in the incubator can use liquid CO2 or gas, no matter which kind of CO2 is used to supply the pipe, the pipe can not be too curved to ensure the smooth flow of gas. Generally, the CO2 cylinder is used, and the pressure control table can be connected.
(6) Zeroing of CO2 content, after the temperature and humidity in the tank are stable (usually three days), turn the CO2 adjustment knob to adjust the number of the display panel to 0.00, and repeat the adjustment if necessary after 5 minutes. Until the reading on the display tray is stable. Turn on the CO2 injection switch (injection light is on), adjust the CO2 setting to the desired concentration so that the concentration reaches the set concentration (the injection lamp is extinguished) and maintain it for at least 10 minutes. Thereafter, the CO2 content in the tank is automatically adjusted by the CO2 controller.
(7) Adjusting the humidity of the CO2 incubator First press the humidity adjustment knob, then turn the humidity adjustment knob to the desired culture humidity, and then adjust the humidity automatically by the humidity regulator.
(1) The incubator should be placed in a relatively stable position and away from heat sources to prevent temperature fluctuations and microbial contamination.
(2) Before turning on the power, add a certain amount of distilled water in the incubator according to the instruction manual (add the amount of disinfectant to the water added, see the instructions for details) to avoid burning the machine.
(3) When the water is added to a certain amount, the alarm light is on, that is, the water supply is stopped, and the power switch is turned on, that is, the heating is started, and the temperature controller is adjusted to the required temperature.
(4) When the temperature reaches the required temperature, the heating is automatically stopped. When the required temperature is exceeded, the over-temperature warning light is on and an alarm sounds.
(5) The CO2 used in the incubator can use liquid CO2 or gas, no matter which kind of CO2 is used to supply the pipe, the pipe can not be too curved to ensure the smooth flow of gas. Generally, the CO2 cylinder is used, and the pressure control table can be connected.
(6) Zeroing of CO2 content, after the temperature and humidity in the tank are stable (usually three days), turn the CO2 adjustment knob to adjust the number of the display panel to 0.00, and repeat the adjustment if necessary after 5 minutes. Until the reading on the display tray is stable. Turn on the CO2 injection switch (injection light is on), adjust the CO2 setting to the desired concentration so that the concentration reaches the set concentration (the injection lamp is extinguished) and maintain it for at least 10 minutes. Thereafter, the CO2 content in the tank is automatically adjusted by the CO2 controller.
(7) Adjusting the humidity of the CO2 incubator First press the humidity adjustment knob, then turn the humidity adjustment knob to the desired culture humidity, and then adjust the humidity automatically by the humidity regulator.
Marine Tourism Food,Shrimp Skin,Seaweed Snacks,Dried Shrimp
Zhoushan Fudan Tourism CO., LTD , https://www.fudanfood.com