How to properly install and adjust the tablet press mold

Posted on

Die mounting before tableting machine, a tableting machine to be cut off the power, remove the cover, the rush rails, hopper, feeder. Open the right door, gradually clean the working surface of the turntable, the die hole and the die for installation, and apply some vegetable oil outside the middle die and the punch to adjust the thickness of the film to 5 or more.
How to install a circular piece
Install the mold in the tablet press, loosen the embossed screw screwed on the upper rail cover, pull out the cover, and use the middle die to hit the middle die from the punching hole to fit the middle die into the middle die hole. The Chinese model must never be higher than the working surface of the turntable, and should be checked one by one to avoid mistakes. When installing the middle mold, turn the inner test wheel of the lower part of the machine to make the turntable rotate clockwise and then fix it with the middle mold screw.
Install the punch on the tablet press, remove the cover on the upper rail guide, and then gradually insert the upper punch into the hole, rotate the punch with the thumb and forefinger, and check that the head enters the middle mold and slides flexibly. The hard rub phenomenon is acceptable. The upper punch is fully assembled and the cover is fastened.
The punching machine is installed under the punching machine, and the lower rail is removed. The loading method is the same as the upper punching. After loading, the lower rail is mounted on the upper rail and fastened with screws. (Note that the bottom plate must be placed close to the outer circle when installing the upper rail)
After the complete set of tablet presses are loaded, turn the handwheel to rotate the turntable for two weeks. Observe the operation of the upper and lower punches into the middle die hole and on the rail guide. It should be flexible, without collision and hard rubbing. It should be noted that when the lower punch rises to the high point of Zui (ie, the exit), it should be higher than 0.05-0.15 of the turntable working face, so as not to damage the punch and other parts, then start up, idle for 5 minutes, and run smoothly before putting into production. .
The installation of the die-shaped mold of the tablet press (the geometric shapes such as triangle, ellipse and rectangle are called special shapes)
First install the guide flat key on the upper punch and fasten it with screws.
The punch and the middle die on the tablet press must be installed simultaneously. Press the guide button to insert the upper punch into the upper punch. Up and down East China is flexible, no hard rubbing phenomenon. Then lift the upper punch and put on the middle mold. Put the head of the upper punch into the hole of the middle die, align the middle die with the die hole, place it flat, and tap the tail of the upper punch with a stick to drive the middle die. After the middle mold enters the die hole, the plane cannot be higher than the turntable working face. Then tighten the middle mold screw, check that the head of the punch enters the middle mold and slide it up and down flexibly, and no collision or hard rub is acceptable.
The installation of the punch under the tablet press. Remove the lower rush rail and install the ram. Check the head of the lower punch into the middle mold to move up and down. It should be flexible, no collision and hard rubbing. After all the lower punches are installed, the lower rails are mounted on the upper rails and fastened with screws. (Note that the bottom plate should be placed close to the outer circle when installing the upper rail)
After the full set of middle molds is installed, turn the handwheel to rotate the turntable for 2-3 weeks. Observe the movement of the upper and lower punches into the middle die hole and the upper and lower rails, without collision and hard rubbing. Note that when the lower punch rises to the high power of the Zui (ie, the exit), it should be 0.05-0.15 mm above the turntable plane. Then start the motor and idle for 5-10 minutes. It can be put into normal production until the operation is smooth and there is no abnormality.

2-Piece Ostomy pouch MDK-BO-02 800ML

1-Piece Ostomy Pouch

A one-piece colostomy bags, drainable pouching system designed to be opened at the bottom when emptying. These colostomy bag machine are most suitable for colostomies or ileostomies. Ostomy bag colostomy barrier is a standard wear skin barrier that is gentle to the skin and allows for frequent pouch removal. To close the pouch, use the curved, beige clamp. Soft, beige disposable colostomy bag pouch panels on body side help provide comfort.

The features are soft and flex,standard wear, skin barrier, flat. The Chassis made in 100% hydrocolloid No tape border. Cut-to-fit skin barrier. Ultra-clear odor-barrier pouch film. Curved, beige pouch clamp. With comfortable ware pouch panel body side only. Not made with natural rubber latex.

Ostomy urostomy colostomy bag care products consist of sodium carboxymethylcellulose, adhesives made from medical hot melt adhesives, and separator paper or separators. Nursing equipment for ileum, colon, rectum or urethral stoma,The coloplast colostomy bag comes into contact with intact skin and intestinal lumen,Non-sterile supply. Colostomy bag reusable for stoma washing, care and collection of excreta and skin care around the stoma.

Use disposable colostomy bag, make sure the skin around the stoma is clean and dry before use. Remove the bags for colostomi from the package and separator or paper. Reshape the coloplast colostomy bag into the desired shape and size to fit the skin around the stoma. Apply the colostomy convatec bag to the skin around the stoma,adjust the shape of the paste again,Gently press so that it is firmly flat on the skin. Attach the stoma colostomy bag undercarriage to the stoma. The colostomy bag care can be peeled off the skin, don`t reuse. These one-piece-colostomy bag or two-piece-colostomy-bag are non-sterile product and is valid for three years under the condition of meeting the storage conditions.

1-Piece Ostomy Pouch,One Piece Ostomy Bags,One Piece Ostomy Pouch,1 Piece Ostomy Bag

Henan Maidingkang Medical Technology Co.,Ltd , https://www.mdkmedicales.com